Do you really need a range hood? A ductless range hood works by forcing the contaminated air through a charcoal filter to clean it and this is important before installing it and a ductless hood can be installed anywhere since they do not need to vent side to the outside of your home. Adding a ductless range hood to your kitchen gives the kitchen a whole look.
If you are exploring upgrading options for your kitchen, you should consider installing a ductless range hood although your choice of range hood would be dictated by your kitchen construction. Range hoods bring vertical value quickly and provide a new, sleek look to your kitchen.
Installing a ductless range hood is not as complicated as it sounds and you can have it fixed in no time with a well explanatory guide hence in this article, we have carefully listed things you need and how to install a ductless range hood.
Things you will need to install a ductless range hood
- Tape measure
- Rangehood
- Pencil
- Level
- Old workbox
- Electrical outlet(duplex 15-amp)
- Cardboard
- Electrical circuit tester
- Drywall saw
- Mallet
- Screwdrivers (Phillips-head and slot head
- Wire stripper
- Tracing paper
- ⅛-inch drill bit
- Drill
- Stud finder
How To Install A Ductless Range Hood
Since they are ductless, the surrounding collection or the refrigerator can be mounted conveniently and you don’t have to cut opening troughs between the ceiling and roofline. Before adding a ductless unit, check your local building code for approval.
Regarding our purposes, we believe you had an electrical circuit wire running from the circuit breaker box to the position of the outlet behind the vertical “chimney” of the portfolio roof.
Processing
Find a centre point on the wall:
Measure the middle of your wall by means of a tape measure. When you work between two large cabinets, weigh and mark the halfway between them.
Double-check the middle to guarantee that your cooking range is centre-long. Use a map and draw a vertical line from your selection to the ceiling after you have reached the central point.
- Check your Measurements:
Each hood is fitted with guidelines for the distance to be placed; the rest can be installed over the range from 29 “to 34.” Measure the amount of space available for the hood from the top of the range to the ceiling.
Now it is necessary to determine where the hood and chimney can be positioned in the space available so that the hood size meets the height required.
Place the chimney above the cap and measure the shorter length from the lower of the cap up to the top of the chimney.
Make sure the electric wire drop suits between the top of the hood and the roof for the outlet.
- Install an electrical box in the drywall:
Place the “old work’ box face to face with the wall where the wires are. Consult the sides of the box to show the space in which the box falls. The outlet must be located somewhere in the centre and in the area covered by the hood chimney.
Test that you have the right breaker off using an electrical circuit tester. Check the electrical tester always double for a circuit you know to ensure that the tester works. If the cables are active, locate and turn off the circuit breaker that governs the circuit.
Use a drywall screw to cut along the pre-marked box line once the circuit is completed. Starting with a small hole is easier and check for wires or other hazards when you are moving.
Use a knife to rub the drywall. Pry open the holes behind the ‘ old work ‘ box and run them through the circuit wires. Once you loop the wires into the package, put the box in the opening wall. To lock it in place, tighten the twists on the box.
- Connect the electrical outlet:
Prepare each insulated wire by scraping 1/2 “of the insulation with a stripper. Then bend the exposed end of each wire to a tight ‘ J ‘ shape. Loosen one of the brass-coloured twists on the electric cover, then loop the ‘ J ‘ on the black wire around the brass (warm) screw in a clockwise direction. Keep to the screw tightly.
Put the white wire in the same way on one (neutral) silver screw. Eventually, attach the copper bare wire in the bottom of the receptacle to the green (ground) screw. Stick the wires carefully into the box and make sure that no ties are loosened. Attach the electric outlet straps with the box by mounting.
- Mark wall for the bracket:
Hold a large plot of plot paper to the back of the hood (where the bracket holes are located) and map the holes on the paper. Test the stage 1 dimensions by holding the paper on the board. Mark the wall for the screws of the drywall.
Hammer the pilot hole in the chosen position and insert the drywall screws in with a hammer and one 1/8 inch bit until they just protrude. The hood range is suspended from these screws, as wall pads are found and the hood range firmly anchored.
On the ceiling directly on your centre line place your chimney bracket using drywall screws
Pull the cover off the screws and secure the screws. Use a pin finder to find two pins running behind the hood. Mark the studs once they have been found. Anchor the hood to the stubs in marked lines from below the range hood. Both traces are below the hood and are not visible.
Plug the hood into the electric outlet until you attach the chimney. Turn the hood in the range and make sure that all works properly. Slide the chimney into the hood set attachment hardware. Nothing in the chimney needs to be added. Mount the recirculation air filters. It recirculates the air to force it into holes in a chimney. The hood is ductless. Connect the chimney with the provided screws to the body of the roof.
Is ductless range hood worth it?
Yes, a ductless range hood is worth it as it is effective in filtering some grease and cooking odours from the air although they are not effective when it comes to keeping your kitchen cool when you cook as they do not remove heat and humidity. A ductless range hood does a decent job of trapping grease and odours and adding it to your kitchen alcove makes the kitchen look whole.
